Hyundai Sonata Timing Chain Replacement

Hyundai Sonata Timing Chain Replacement in Batumi

We only do a Hyundai Sonata timing chain replacement once we've proven the noise is the chain and not rod bearings or a cam phaser. Then the whole set goes in: chain, hydraulic tensioner, tensioner arm and guide. PRO SERVICE, Batumi, Airport Highway 212M. Labor from 180 GEL. It takes 1-2 working days. Parts are billed separately.

Which Sonata has a chain

Every Sonata you actually see on the road in Batumi, from the NF on, is a chain engine. The belt stayed with the older generation.

GenerationEnginesCam drive
EF (1998-2005), TagAZ build until 20122.0 Sirius, 2.7 V6 Deltabelt
NF (2005-2010)2.0 and 2.4 Theta, 3.3 V6 Lambdachain
YF (2010-2014)2.4 GDI and MPI Theta II, 2.0 turbo, LPI gas versionschain
LF (2014-2019)2.4 GDI, Nu 2.0, 1.6 and 2.0 turbo, LPIchain
DN8 (2019 on)Smartstream 2.5, 1.6 turbo, LPIchain

An old EF is a different job, see timing belt replacement. The non-turbo 2.0 on a YF or LF can be either Theta II or Nu, so we check the engine code. The 3.3 V6 has more than one chain and a lot more labor than the inline four. The rest of what goes wrong on this car, including the 2.4 GDI knock and the gas versions, is on the Hyundai Sonata repair page.

Chain, rod bearings or cam phaser

That's the first thing we sort out. A new chain on an engine with spun rod bearings is money down the drain.

Chain. A rattle for 1 to 3 seconds right after a cold start, loudest after a night or a few days parked. It comes from the front right, on the alternator belt side. Once the oil pressure is up, it goes quiet.

Rod bearings. A dull knock that stays when the engine is hot and speeds up when you blip the throttle. Hot idle oil pressure is low. Now we're talking engine rebuild, not a chain.

CVVT phaser. Clicking and ticking at idle, codes P0011 or P0014. Often it's the oil control valve with a clogged screen, and the chain is fine.

Codes that point to the chain

  • P0016: crank and intake cam position out of sync.
  • P0017: same thing for the exhaust cam.

A lone P0016 can be a sensor, wiring or a CVVT valve. When P0016 and P0017 show up together, both cams have shifted against the crank, and that is the classic stretched chain picture. On the scanner we compare actual cam angle to target on a warm engine. If you can leave the car overnight, we listen to the cold start in the morning.

Why Sonatas in Batumi stretch chains

The chain lives on oil. The hydraulic tensioner holds it with oil pressure, and with dirty oil or a low level it can't keep up. A Sonata cab works all day, idles for ages at the airport stand, and the oil gets changed by mileage while engine hours pile up much faster. Add summer heat and the traffic coming into town.

The Korean LPI gas cars are their own story. The timing hardware is the same, but the mileage is usually huge and nobody knows the service history.

How we do it on a Theta II 2.4

  1. Scanner, listen, check oil pressure. Confirm the stretch.
  2. Support the engine, remove the right mount, the alternator belt and the crank pulley.
  3. Pull the front timing cover. It's sealed with RTV and meets the oil pan, so we scrape both faces down to bare metal.
  4. Cylinder one at top dead center. The new chain has colored links, we line them up with the marks on the cam sprockets and the crank sprocket.
  5. Fit the chain, tensioner arm, guide and a new tensioner held by its pin. The pin comes out once everything is in place.
  6. Two turns of the crank by hand, marks checked again.
  7. New crank seal, fresh RTV, oil and filter. The sealant gets time to set.
  8. Start it, clear codes, watch cam timing on live data. Next morning, one more cold start to listen to.

Sprockets and CVVT phasers get replaced only if we see worn teeth or they rattle on their own. The 2.4 also has a balance shaft and oil pump module down in the pan with its own chain. If the pan is off, we look at that one too.

Price

JobPrice, GEL
Timing chain Sonata 2.0, 2.4 (labor)from 180
Diagnostics: chain or bearingsfrom 30
Timing belt on an old EFfrom 90
Engine rebuild if the bearings knockfrom 1000

FAQ

How much is a timing chain on a Sonata 2.4?

Labor from 180 GEL. The 3.3 V6 costs more because it has more chains. We order the kit by VIN.

At what mileage does a Sonata need a new chain?

There's no set interval. It's done on symptoms: cold start rattle, cam timing codes, a tensioner that's run out of travel. On a cab with stretched oil changes that comes sooner than on a private car.

It rattles only in the morning, quiet the rest of the day. Is it time?

Most of the time that's the start of stretch. But first we check the oil level and what's in there: with low oil the tensioner takes longer to pump up and rattles even on a healthy chain.

Can I drive with P0016 and P0017?

Briefly and gently. If the chain jumps a tooth, the valves can hit the pistons and the bill multiplies.

Is the chain different on an LPI Sonata?

No, the timing hardware is the same. We don't touch the gas system for this job.

●  06 · Contact

Leave a request — we'll call back and book an inspection

Tell us what happened to the car. We'll call back, answer your questions and find a time. We give the exact price after an inspection: photos don't always show the damage.

By sending the request you accept the privacy policy.

Or message us — we reply right there:

Address
Airport Highway 212M, Batumi, Georgia
Phone / WhatsApp / Telegram
+995 599 66 66 75 · WhatsApp · Telegram
Directions
Google Maps ↗Yandex ↗Waze ↗
PRO SERVICE entrance