Cylinder Head Repair in Batumi
Cylinder head repair in Batumi at PRO SERVICE (Airport Highway 212M). We take the head off, check it for flatness and pressure-test it for cracks, then rebuild the valve train: valves lapped or replaced, plus seats, guides and stem seals. It goes back on with a new gasket. Labor from 300 GEL, takes 3-5 working days. Parts and machining are priced after inspection.
Signs of a cylinder head problem
- Low compression in one cylinder. Very often that's a burnt valve or one that doesn't seal.
- Blue smoke at start-up or after a long downhill points to worn stem seals or guides. You'll notice it easily on Adjara's mountain roads when you're using engine braking.
- A misfire that won't go away even after new plugs and coils.
- Bent valves after the timing belt snapped or the chain jumped a tooth.
- Overheating can crack or warp the head; the signs are disappearing coolant and milky oil.
- Ticking from the top end, which can be the camshafts, their journals or hydraulic lifters.
What we do
- Remove the head, strip the valve train, clean everything.
- Inspection: deck flatness, a pressure test for cracks, valve-to-guide clearance, seats, camshafts and journals.
- Valves get lapped or replaced. A bent valve is always replaced.
- Burnt seats are re-cut or replaced.
- Guides and stem seals are replaced if there's play and the engine is using oil.
- A warped deck is resurfaced, staying within the allowed limit.
- Reassembly and valve clearance adjustment (on engines without hydraulic lifters, see valve adjustment). The head goes on with a new gasket and bolts torqued to spec.
Head repair or just the gasket
If the head is flat, the valves are fine and coolant is only escaping through the gasket, a head gasket replacement is all you need. If the cylinders and rings are worn as well, fixing only the head is pointless, and we'd talk about an engine rebuild instead. A compression test and borescope settle this before the head comes off.
What affects the cost
The number of valves and camshafts matters most: 8, 16 or 24 valves, single or twin cam, and a V engine has two heads. Then it's how many valves, seats and guides have to be replaced, and whether the head needs resurfacing and a pressure test. Many people also do the timing belt or chain at the same time, since the head is off anyway.
Price
| Work | Price, GEL |
|---|---|
| Cylinder head repair (remove, strip, reassemble) | from 300 |
| Valve stem seal replacement | from 200 |
| Head gasket replacement | from 250 |
FAQ
Can valve stem seals be replaced without removing the head?
On many engines, yes, using a special tool. If the guides are worn too, the head has to come off.
My valves bent after the belt snapped. What next?
We take off the head, replace the valves and check the guides and pistons. To avoid a repeat, have a look at timing belt replacement.
Does the head need resurfacing every time it comes off?
No. Only when flatness is out of tolerance, which we check with a straightedge and a feeler gauge.
How much does cylinder head repair cost?
Labor from 300 GEL. Parts and machining are added after inspection.
How long will it take?
3-5 working days. It mostly depends on getting valves and guides.
● 06 · Contact
Leave a request — we'll call back and book an inspection
Tell us what happened to the car. We'll call back, answer your questions and find a time. We give the exact price after an inspection: photos don't always show the damage.
By sending the request you accept the privacy policy.
Or message us — we reply right there:
- Address
- Airport Highway 212M, Batumi, Georgia
- Phone / WhatsApp / Telegram
- +995 599 66 66 75 · WhatsApp · Telegram
- Directions
- Google Maps ↗Yandex ↗Waze ↗
