How to Fix Rust on Rocker Panels and Wheel Arches
Updated: · PRO SERVICE
How to fix rust on rocker panels depends on how deep it goes. Surface rust gets cleaned to bare metal, primed and sealed. Rust-through gets cut out, and new metal is welded in. Painting over the spot won't work, because the corrosion keeps going underneath. Rocker panels and wheel arches rust first since they take the water, sand and salt, and the closed cavity inside a rocker can hold moisture for weeks.
Why rocker panels and arches rust
A rocker panel is a hollow box. Water finds its way in through drain holes and gaps, but it has a hard time getting out, especially when the drains are clogged with dirt. On top of that, sand and small stones thrown by the wheels chip the paint and protective coating on the arches and the lower edge of the rocker. Sea air does the rest: the humidity and salt speed up corrosion on any metal left exposed.
- Joints and seams. Rust often starts where the arch meets the fender or rocker panel, at thin metal and spot welds.
- Old repairs are another source. Filler laid over rust that was never removed traps moisture, and the corrosion carries on under it.
Three stages of corrosion
| Stage | What it looks like | What is usually done |
|---|---|---|
| Surface | Orange spots, chips with rust at the edge | Clean to bare metal, converter, primer, paint, rustproofing |
| Under paint | Paint bubbles, flakes off | Open up, clean, check metal thickness, then as above or weld in |
| Rust-through | Holes, metal crumbles, flexes when pressed | Cut out the area, weld in a repair section or a whole panel |
Here's the thing to remember. The spot you can see is almost always smaller than the real damage, and under a coin-sized bubble there's often an area several times larger.
How to check yourself
- Look over the lower edge of the rocker panels and arches in good light. A lift is ideal, or use a flashlight from below.
- Press on any bubbles with a finger. If the metal flexes or crunches, the corrosion is deep.
- Check the drain holes under the rocker panels and doors. When they're clogged, water just sits inside.
- Look behind the wheel arch liners. The plastic collects dirt, and the arch behind it often rusts without anyone noticing.
- Pay attention to the seams between the arch, fender and rocker panel.
Repair options
Cleaning and painting only works for surface rust, and the corrosion has to come off completely, down to clean metal, or it'll be back.
If part of the rocker panel or arch is eaten through, we cut that part out and weld in a repair section, either a ready-made one or one shaped from sheet metal. Then the seam gets treated, the cavity is sealed with rustproofing and the panel is painted.
Replace the whole rocker panel. That's the call when corrosion runs the full length or the panel is already deformed. The rocker panel is a structural part of the body and affects its rigidity, so glued-on patches won't do the job here.
Fiberglass or epoxy repair. You'll find these offered, but the metal underneath keeps rusting and the rocker panel doesn't get its strength back. Treat it as a temporary measure. It isn't a repair.
Why rustproofing is needed after repair
New metal and fresh weld seams with no protection rust faster than the old metal does. So once the welding is done, the inner cavities of the rocker panel and arch get cavity wax, and the outside gets a protective coating. Don't skip this step to save money.
How to slow corrosion
Wash the arches and rocker panels from below, especially after the beach or muddy roads, and keep the drain holes clear. When you spot a chip on a rocker panel, seal it right away, before rust gets under the paint. And rustproof ahead of time, rather than after the holes show up.
Where to fix rust in Batumi
At PRO SERVICE (Batumi, Airport Highway 212M) we handle rocker panel repair, wheel arch repair and rustproofing.
FAQ
How much does rocker panel repair cost?
It depends on whether it needs a cleanup, a welded section or a full panel, and you only know that once the rust is opened up. Reference price: from 400 GEL per side.
Can I just paint over the rust?
If it isn't taken down to bare metal, it'll come through within months. Paint without cleanup is purely cosmetic.
Is rust on rocker panels dangerous?
Rust-through is, since the rocker panels give the body its rigidity and protect you in a side impact. Surface rust isn't yet, but it's better to stop it now.
Does the whole arch need replacing?
Usually not. The rear arches are part of the body, so the damaged area is cut out and a repair section is welded in.
● 06 · Contact
Leave a request — we'll call back and book an inspection
Tell us what happened to the car. We'll call back, answer your questions and find a time. We give the exact price after an inspection: photos don't always show the damage.
By sending the request you accept the privacy policy.
Or message us — we reply right there:
- Address
- Airport Highway 212M, Batumi, Georgia
- Phone / WhatsApp / Telegram
- +995 599 66 66 75 · WhatsApp · Telegram
- Directions
- Google Maps ↗Yandex ↗Waze ↗
